The last two versions are available for download:Ĭisco Packet Tracer is a powerful network simulation software from Cisco Systems Inc which can simulate/create a network without having a physical network. There will be times when you want to download the previous versions of Packet Tracer.
Let’s walk through the registration and download process here. Registering is helpful because you will also need to sign in with the same ID when you run the simulation tool.
Just keep reading… How to download the latest version of Cisco Packet Tracer Cisco Packet TracerĬisco Packet Tracer is free to download but you need to register for Netacad Networking Academy which is also free.
You can simulate a complete Cisco network without actually connecting the devices physically.ĭon’t worry, we will show you all the steps to download and install the Cisco Packet Tracer software. Step 3: Configure IP addressing on PC4, including the default gateway.Cisco Packet Tracer is a powerful network simulation tool for Cisco networks. Step 2: Configure IP addressing on S3, including the default gateway. Step 1: Configure IP addressing on R1 LAN interfaces. Implement the following steps to complete the addressing configuration. Most of the IP addressing is already configured on this network. Part 2: Assign IP Addresses to Network Devices and Verify Connectivity Assign the last usable IP addresses to the hosts. Assign the second usable IP addresses to the switches.ĭ. Assign the last usable IP address for the WAN link.Ĭ. Assign the first usable IP addresses to R2 for the LANs links. Assign the first usable IP addresses to R1 for the two LAN links and the WAN link.ī. Assign Subnet 4 to the WAN link between R1 to R2: – 192.168.100.128 /27 Step 3: Document the addressing scheme.įill in the Addressing Table using the following guidelines:Ī. Assign Subnet 3 to the LAN connected to the GigabitEthernet 0/1 interface of R2: – 192.168.100.96 /27Į. Assign Subnet 2 to the LAN connected to the GigabitEthernet 0/0 interface of R2: – 192.168.100.64 /27ĭ. Assign Subnet 1 to the LAN connected to the GigabitEthernet 0/1 interface of R1: – 192.168.100.32 /27Ĭ. Assign Subnet 0 to the LAN connected to the GigabitEthernet 0/0 interface of R1: – 192.168.100.0 /27ī. Step 2: Assign the subnets to the network shown in the topology.Ī. Fill in the Subnet Table, listing the decimal value of all available subnets, the first and last usable host address, and the broadcast address. Calculate the binary value for the first five subnets. Note: If your answer is less than the 25 hosts required, then you borrowed too many bits.Į. How many usable hosts does this create per subnet? 2^5 – 2 = 30 hosts How many subnets does this create? 2^3 = 8 subnets (support subnet zero)ĭ. How many bits must be borrowed to support the number of subnets in the topology table? 3 bitsĬ. Based on the topology, how many subnets are needed? 5ī. Part 1: Design an IP Addressing Scheme Step 1: Subnet the 192.168.100.0/24 network into the appropriate number of subnets.Ī. The connection between R1 to R2 will require an IP address for each end of the link. Each LAN in the network requires enough space for, at least, 25 addresses for end devices, the switch and the router. In this activity, you are given the network address of 192.168.100.0/24 to subnet and provide the IP addressing for the network shown in the topology. Part 2: Assign IP Addresses to Network Devices and Verify Connectivity Scenario Packet Tracer – Subnetting Scenario 1 Addressing Table